A three-part car lashing strap consists of an integrated assembly engineered with three distinct components: a main tensioning webbing strap fitted with a deck hook, a heavy-duty ratchet tensioner, and a separate strap controller (connecting belt / anti-slip sleeve). Unlike standard two-part tie-down straps, this setup separates the wheel-gripping zone from the mechanical tensioning path.
Secures the vehicle exclusively by its unsprung mass (tires and wheel rims). Compressing chassis suspension during transport causes straps to slacken as shocks bounce, whereas wheel lashing maintains rigid, constant tension.
Directs 100% of the restraint force through the tire tread. Webbing and metal ratchets never contact alloy wheel faces, bumpers, or rocker panels, eliminating expensive transit damage claims.
The main strap, ratchet, and strap controller must operate as a certified matched set. Intermixing components across brands invalidates the system's certified ETA friction value.
Car carrier operations across Europe and international transit corridors are governed strictly by EN 12195-2 and the German VDI 2700 Sheet 8.1 & 8.2 guidelines (tightened substantially in the 2024 revisions):
| Regulatory Parameter | Passenger & Light Commercial (≤ 4.5 t) | Medium & Heavy Commercial (4.5 t – 20 t) |
|---|---|---|
| Governing Standard | VDI 2700 Sheet 8.1 / EN 12195-2 | VDI 2700 Sheet 8.2 / EN 12195-2 |
| Lashing Capacity (LC) | ≥ 1,500 daN | ≥ 2,500 daN |
| Standard Tension Force (STF) | ≥ 330 daN | ≥ 500 daN |
| Webbing Elongation (ε) | ≤ 4% at LC | ≤ 4% at LC |
| Identification Labeling | Mandatory ETA Rating Marked | Mandatory ETA Rating Marked |
| Webbing Width | 35 mm / 50 mm | 50 mm |
High-tenacity, low-stretch polyester webbing fitted with a 360° swivel hook or single claw hook designed to engage trailer perforated deck slots cleanly at any angle without twisting.
Heavy-duty, short-handle ratchet designed for confined wheel-well clearance. Precision gear teeth ensure the mandatory STF (≥ 330 daN) is achieved with minimal operator fatigue.
A reinforced flat connecting belt with dual eye loops. Positioned on the tire's outer shoulder, it prevents the main tensioned strap from abrading against rubber and keeps the assembly centered.
Applying a three-part car lashing system correctly follows a consistent sequence regardless of vehicle type. Position the vehicle centrally on the transport platform and apply its parking brake first. Place the wheel-engaging section around the tire and rim — most passenger vehicle setups use a three-point pattern, though loading position and vehicle weight can require adjusted configurations. Attach the controller's hook to the deck's approved anchoring point, then tension the webbing using the ratchet until it reaches the strap's rated standard tension force. Finally, check that the webbing has no contact with the tire surface or any sharp edges along its length, and confirm the vehicle sits stable before the carrier moves.
Always engage the transported vehicle's parking brake and position it centrally on the deck before attaching wheel straps.
Never rely on a single wrap on the ratchet mandrel. At least 2 full wraps are legally required to prevent dynamic slippage during emergency braking.
Retire straps immediately if edge cuts, tear damage exceeding 10% of width, melted fibers from exhaust heat, or chemical burns are found.
Every strap must retain its factory label detailing LC, STF, elongation (≤ 4%), manufacturer name, and EN 12195-2 / VDI 2700 compliance.
In high-volume vehicle logistics, the three-part car lashing system provides the optimal combination of rapid loading efficiency and zero-damage security. By anchoring the unsprung wheel directly to perforated carrier decks, it eliminates suspension bounce and protects luxury and commercial finishes.
Specifying certified H-Lift car fixing lashing straps compliant with EN 12195-2 and VDI 2700 guarantees full legal compliance during European cross-border freight audits while ensuring every vehicle arrives safely at the showroom dock.