For decades, Grade 80 (800 N/mm² nominal tensile strength) served as the global baseline for overhead alloy chain slings, later joined by Grade 100 (1,000 N/mm²) for heavier lifting. Yet on wind turbine sites, offshore platforms, shipyard dry docks, and heavy structural steel jobs, bulky multi-leg slings create severe ergonomic strain, slow hookup cycles, and limit crane hook clearance.
Grade 120 Chain Components (1,200 N/mm² nominal breaking stress class) represent the next generation of rigging metallurgy. By combining vacuum-degassed nickel-chromium-molybdenum specialty alloy steel with computer-controlled quench-and-temper thermal cycles, Grade 120 delivers a +50% capacity increase over Grade 80 and a +20% capacity increase over Grade 100 components of identical nominal diameter.
The table below compares nominal Working Load Limits (WLL) across Grade 80, Grade 100, and Grade 120 systems, illustrating how Grade 120 enables size downsizing at equal lifting capacity:
| Nominal Chain Size (d mm / Inch) |
Grade 80 WLL (800 MPa) |
Grade 100 WLL (1,000 MPa) |
Grade 120 WLL (1,200 MPa) |
Grade 120 Proof Load (2.5×) |
Grade 120 MBF (4×) |
Practical Downsizing Advantage (G120 vs. G80) |
|---|---|---|---|---|---|---|
| 6 mm (7/32") | 1.12 t | 1.40 t | 1.70 t | 41.7 kN | 66.7 kN | Bridges gap to 7 mm G80 (1.50 t) |
| 7 mm (1/4") | 1.50 t | 1.90 t | 2.36 t | 57.9 kN | 92.6 kN | Replaces 8 mm G80 (2.00 t) |
| 8 mm (5/16") | 2.00 t | 2.50 t | 3.00 t | 73.6 kN | 117.7 kN | Replaces 10 mm G80 (3.15 t) → ≈ 35% lighter |
| 10 mm (3/8") | 3.15 t | 4.00 t | 4.80 t | 117.7 kN | 188.4 kN | Replaces 13 mm G80 (5.30 t) → ≈ 38% lighter |
| 13 mm (1/2") | 5.30 t | 6.70 t | 8.00 t | 196.2 kN | 313.9 kN | Replaces 16 mm G80 (8.00 t) → ≈ 35% lighter |
| 16 mm (5/8") | 8.00 t | 10.00 t | 12.00 t | 294.3 kN | 470.9 kN | Replaces 20 mm G80 (12.50 t) → ≈ 36% lighter |
| 20 mm (3/4") | 12.50 t | 16.00 t | 18.80 t | 461.1 kN | 737.7 kN | Replaces 22 mm / 26 mm G80 |
| Series | Type | Typical Use | Main Feature |
|---|---|---|---|
| SLC | Self-locking hook with shortening clutch | Adjustable-length slings | Built-in clutch shortens the leg; the hook locks automatically |
| CSH | Clevis sling hook with latch | Overhead lifting, load attachment | Forged alloy body with spring latch, direct chain connection |
| ESH | Eye sling hook with latch | Chain slings with a connecting or master link | Closed eye, latch, 6-13 mm, WLL 1.8-8 t |
| CNL | Connecting link (hammerlock coupling) | Joining chain to master links and fittings | Pin-closed link for easy assembly and repair |
Under EN 1677, EN 818-4, ASME B30.9, ASME B30.10, and OSHA 1910.184, Grade 120 chain components must undergo pre-shift visual checks and periodic documented inspections. Condemn immediately if:
Q: How much weight can I save by upgrading from Grade 80 to Grade 120 chain components?
A: Because Grade 120 offers a +50% higher WLL than Grade 80 at the same nominal diameter, you can step down one full nominal size while maintaining virtually identical lifting capacity. Across a multi-leg chain sling assembly, downsizing by one size typically reduces total rigging deadweight by 30% to 38%, reducing rigger fatigue and speeding up hookups.
Q: Why does Grade 120 have a lower maximum temperature limit (+300°C) than Grade 80 (+400°C)?
A: Grade 120 achieves its ultra-high 1,200 N/mm² tensile strength through specialized micro-alloying and precision lower-temperature tempering cycles. Exposing Grade 120 steel to temperatures above +300°C over-tempers the fine-grain microstructure, permanently reducing its tensile strength back toward lower grades. For extreme high-heat operations up to +400°C, Grade 80 alloy components remain the required choice.
Q: Are Grade 120 chain fittings proof-tested to the same safety factor as Grade 80 and Grade 100?
A: Yes. Under EN 1677, EN 818, and ASME B30.9/B30.10, Grade 120 components adhere to the exact same 4:1 Design Safety Factor (MBS = 4 × WLL) and undergo 100% factory proof-load testing at 2.5× WLL along with non-destructive Magnetic Particle Inspection (MPI).