H-Lift Industries Co.,Ltd.
Lifting Solution Specialist
By Charlie | 16 May 2022 | 0 Comments

What do the units N, daN, kN & kgf mean?

What do the units N, daN, kN & kgf mean?

The newton (symbol: N) is the International System of Units (SI) derived unit of force. It is named after Isaac Newton in recognition of his work on classical mechanics, specifically Newton's second law of motion. 

One newton (1 N) is the force required to accelerate a mass of one kilogram at a rate of one metre per second squared (one meter per second per second) in the direction of the applied force. 

It is common to see forces expressed in dekanewtons (symbol: daN) or kilonewtons (symbol: kN). 

1 dekanewton (daN) = 10 newtons (N)

1 kilonewton (kN) = 100 dekanewton (daN) = 1000 newtons (N)

On Earth's surface, a mass of 1 kg exerts a force of approximately 9.8 N (down), or 1.0 kilogram-force, 1 kgf.

1 kilogram-force (kgf) = 9.80665 newtons (N)

The approximation of 1 kg corresponding to 10 N is sometimes used as a rule of thumb in everyday life and in engineering. 

An amusing rule of thumb to help remember the newton (N): On earth, 1 N is equivalent to approximately 100 grams (g). Coincidentally, this is about the mass of an apple. So, you can think of 1 N as getting hit on the head with an apple.

Kilonewtons (kN) are often used for stating safety holding values of fasteners, anchors and more in the building industry. They are also often used in the specifications for paragliding, paramotoring, hang gliding and rock climbing equipment (e.g. karabiners and maillons). The safe working loads in both tension and shear measurements can be stated in kN.

1 kN equals 101.97162 kilograms of load, but multiplying the kN value by 100 (i.e. using a slightly pessimistic and easier to calculate value) is a good rule of thumb.

Examples...

  • "Strength: 18KN" = 1800 daN = approx 1800 kg
  • "Breaking strain 1800 daN" = 18 kN = approx 1800 kg
  • "Breaking strain 2000 daN" = 20 kN = approx 2000 kg
  • "Breaking load 2500 kg" = approx 25 kN = 2500 daN
  • "Breaking strain > 2500 daN" = 25 kN = approx 2500 kg
  • "Guaranteed load 26 kN" = 2600 daN = approx 2600 kg
  • "Breaking load 32 kN" = 3200 daN = approx 3200 kg
  • "Breaking strength 40 kN" = 4000 daN = approx 4000 kg 

For more info, see Newton (unit) - Wikipedia, the free encyclopaedia

Working Load Limit (WLL) & Minimum Breaking Load (MBL)

Working Load Limit (WLL) aka Safe Working Load (SWL) is the maximum working load designed by the manufacturer. It is the force that a piece of lifting equipment, lifting device or accessory can safely use to lift, suspend or lower a mass without fear of breaking.

The WLL represents a force that is much less than that required to make the lifting equipment fail or yield, which is usually known as the Minimum Breaking Load (MBL) or Minimum Breaking Strength (MBS).

The WLL is usually marked on the equipment by the manufacturer and is calculated by dividing the MBL by a Safety Factor (SF) i.e. WLL = MBL / SF.

For more info, see Working load limit - Wikipedia, the free encyclopaedia

Leave a Reply

Your email address will not be published.Required fields are marked. *
Name
E-mail
Content
Verification code
ver_code
TAGS